tabledugout8

How to Replace a Saab 9-3 Key The Saab 9-3 is a car that has a large variety of appeal to drivers. It has a powerful engine as well as good visibility. It has a high safety rating. It is crucial to have two keys that work for your vehicle. If you lose only one key, it could be very expensive to add a new one. How to replace the ignition Key in the Saab9-3 If the car key won't start in the ignition you must replace it. This guide will show how to replace the ignition key on the Saab 9-3. You will have to replace the key, buy an additional reprogrammable cell and buy a new case for your key-fob. In replacement saab car keys to older models, the majority of modern Saab vehicles use a transponder in the key-fob, instead of a physical key to unlock and start the vehicle. The issue with this is that the reprogrammable battery inside the key-fob can wear out and not hold a charge for long. This is especially applicable if you are using the same key for the same lock. The good thing is that the battery can be replaced easily by an experienced locksmith. You can also do it yourself if you have the necessary tools and a little bit of patience. The first step is to take the key-fob from its case. Insert an open-ended head into the slot that is in the middle of your case. You must work slowly, as the plastic is extremely thin and can be damaged easily. Once the case is opened and you are able to prepare the new key by combining the lower section of the old key with the transponder and banana on the new key. This will ensure that the new key is properly paired to your CIM, which can make a big difference when replacing the sole key on your Saab 9-3. How to replace the ignition Key on the Saab 900 Unless you have two keys, you'll need to remove the dashboard and steering wheel to gain access to the ignition. Begin by disconnecting the negative battery cable. Once the battery is disconnected, you can remove all the trim pieces and dashboard pieces that surround the steering wheel. Once the dash is taken off, you can push a screwdriver through the opening at the back of the ignition switch and take it out. The ignition cylinder is equipped with a key lock, which could stop the vehicle from starting if you don't have a key. If the ignition switch on your 900 isn't working properly, check whether the key is within the lock or snared inside the barrel. It's also an excellent idea to rotate your keys on a regular basis and keep them clean so that they don't get bent. Saab cars differ from other cars because they don't make use of traditional keys made of metal. Instead, the car is able to recognize the electronic signals from the key fob by a specific chip inside it. If you lose just one key fob that is working, your dealer will charge you an extra fee to replace your computer module (also called the CIM). We can reprogram the EEPROM on your current computer to allow it to accept new keys without the need to replace it. You'll save 50% off the dealer's cost! We call it the SAAB Key PROGRAM. Learn more about it here! How to Replace the Ignition Key on a Saab 9-5 The metal component of a traditional Saab key is simple to copy, and it's also not much of a barrier against vehicle theft. The real protection comes from the electronic part of the key-fob, which is equipped with a chip which recognizes your car once it's put into the ignition switch. Saab has relied on the technology of this anti-theft device for more than 10 years. It's not as effective as an actual lock on the door however it makes the theft of your car much more difficult. That's why every Saab owner should always keep an extra key available. The majority of new Saabs come with two keys at the factory, but you can upgrade them at an agent using a handheld computer, called Tech-2. Tech-2. The cost can be under $400 for the transmitter+transponder (different than the metal key blade/shell that opens the doors and turns the ignition cylinder). The only exception to this rule is the NG 9-3 models, that have more modern, more advanced features that require the use of a key-fob. The dealer will replace the CIM or TWICE module in these cars if all keys are lost, and they'll cost you top dollar for the process. However, we can reprogram the EEPROM in your existing computer and prepare it to accept new keys without replacing the expensive modules. How do I replace the ignition Key on an XC90 Saab If your SAAB 9-3 key fob starts having trouble turning the barrel of the lock, it may be time to replace it. The process is fairly simple and you don't have to go to a dealership. You can do it at home with just a few basic tools. The first step is to prepare the new key. Before you start, disable the anti-theft feature by placing blocks under the rear wheels and activating your handbrake. Put the key into the ignition and then turn the key to the “on” position. This will activate the accessories, however, it won't start the engine. Repeat this five times, and then keep the key in the “on” position. You'll then need to purchase a new case for your key fob. You can find them at any auto parts store, and they're typically quite affordable. Based on the model, you can even purchase them without electronics. To open the case, put an flathead screwdriver into the slot in the middle, and gently work it. The case should split easily, and once you've done that, you'll have access to the internal electronics. Use a flathead screwdriver, which will gently pry open the electronics.